Gas sampling pump kit & accessories

Handy, compact type

Gas sampling pump kitGV-100S

The Gas sampling pump GV-100, pump accessories (3 rubber inlets and lubricant), as well as the instruction sheet are provided in a convenient shoulder bag.

• Gas detector tube system
• Gas sampling pump model No. GV-100 HSE test report

Shoulder-case type

Gas sampling pump kitGV-100LS

The Gas sampling pump GV-100, pump accessories (3 rubber inlets and lubricant), as well as the instruction sheet are provided in a convenient shoulder bag.

• Gas detector tube system
• Gas sampling pump model No. GV-100 HSE test report

Handy, compact type

Gas sampling pump kit with pump stroke counterGV-110S

The automatic sampling counter tells you how many pump strokes you already completed even though GASTEC tubes normally do not require so many pump strokes.
The Gas sampling pump GV-110, pump accessories (3 rubber inlets and lubricant), as well as the instruction sheet are provided in a convenient shoulder bag.

• Gas detector tube system

Safe storage of broken tips

Tube tip holder722

The Tube tip holder doubles as a detector tube tip breaker and a storage receptacle for up to 260 broken tips, thereby preventing glass fragments from scattering.

Safety caps for tubes

Rubber capsDTP-1-20/DTP-2-20

Reusable rubber caps can be attached to the broken edges of the detector tubes as an extra precautionary safety measure. Blue caps can be used with the largest size detector tubes (outer diametre of 7mm) and pink ones with all other tubes. One (1) package contains 20 caps.

No.DTP-1-20(blue)
large-diametre tubes for tube nos. 1HH, 2HT, 2HH, 4HT, 31B (blue)
No.DTP-2-20(pink)
for all type of gas detector tubes except the above

Measuring in manholes, storage tanks, etc.

Extension hoses351A-5/351A-10/351A-30

Extension hoses are available to be attached to the inlet of the gas sampling pump (Model GV-100 or GV-110) and used for remote downward measurement in confined spaces, such as manholes, tanks, etc.
* For twin tube operation, order the Extension hose guard rubber (No.358) . When the extension hose tip needs to be replaced, order the Replacement extension hose guard rubber (No.359) .

351A-5 (for 5m long), 351A-10 (for 10m long), 351A-30 (for 30m long)

• No.351A-30 Instruction manual

Accurate measuring of hot gases

Hot probe/Hot probe holder340/345A

The hot probe is a cooling device for measuring hot gases (60 to 600ºC / 140 to 1112 ºF) such as exhaust from vehicles and incinerators by cooling them down to normal temperatures. The stability of the device is enhanced when it is secured with the hot probe holder (No.345A)

Hot probe holder (Model 345A) can not be used with Twin-tubes and Oxygen tube No. 31B.

Horizontal and vertical measuring

Extension pole350BP-2

Made of lightweight fiberglass and weighing only 590g, the extension sampling pole has a compact body (62.5 cm) for easy portability and can be extended to a maximum length of 2.8m.

• No.350BP-2 Instruction manual

Damage protection for twin tubes

Twin Tube HolderGV500

The twin tube holder protects twin tubes from drop and damage or prevents injury to the user during a measurement.

One hand operation adapterGV-700

GV-700 can maintain a vacuum of 50mL or 100mL in the pump body. This allows the user to attach the appropriate tube to pump, and then in situations where it is necessary, to take the sample using one hand. In the body of the Adapter there is a small rod which can be moved in or out quite easily with one finger.

Kimitsu™Contaminated Vadose Zone Assessment technique

Boring (drill) rod361

Contaminant distribution can be easily and accurately determined.
A hole is drilled in the ground with the boring rod, and the contaminants present in the gas in the hole are measured; by taking measurements at multiple points on a site the exact distribution of contaminants can be assessed.

• The Kimitsu Contaminated Vadose Zone Assessment technique

Kimitsu™ Contaminated Vadose Zone Assessment technique

Extension pole for sub-surface sampling360

Contaminant distribution can be easily and accurately determined.
A hole is drilled in the ground with the boring rod, and the contaminants present in the gas in the hole are measured; by taking measurements at multiple points on a site the exact distribution of contaminants can be assessed.

• The Kimitsu Contaminated Vadose Zone Assessment technique

Dositube holder710

The passive dositube can then be positioned in the worker's breathing zone where it can be attached with a holder and collar clip (separately available : Art.No.710) and the amount of individual exposure can be measured.

• Long-term (time-weighted) measurement detector tubes

Determining gas flow direction in smoke

Smoke tester kit500

Break off both ends of the smoke tube and attach a rubber squeeze bulb to one end of the tube. When the bulb is squeezed, a chemical reaction produces white smoke. This smoke makes the air flow (in ventilation systems/ducts, etc.) visible. A single tube can be repeatedly used for about 50 tests.

• SDS

Determining gas flow direction in smoke

Smoke tube501

This is a supplementary part for smoke tester set No. 500.
A single tube can be repeatedly used for about 50 tests.

• SDS